Right rear wheel locked up ‘21 rtv1140x. 129hrs
- Thread starter Man4fire
- Start date
ok it’s just me and what ever I can get to get the throttle up and take a reading. No fixed tech yet. I got 1440 low idle and 3540 pedal pegged. Call it 3600 cause I had a little bit more 1/2” to go ( stick to short
. Not sure how to check high without pedal and get each reading at the same. But there is still plenty room left on upper stop backed off to get 3800. Manual throttle? I cleaned out the spark arrester today to. Got to 20mph wheels up. Your turn when you have a chance. Bless you.
. Not sure how to check high without pedal and get each reading at the same. But there is still plenty room left on upper stop backed off to get 3800. Manual throttle? I cleaned out the spark arrester today to. Got to 20mph wheels up. Your turn when you have a chance. Bless you. I repeat. You need 3600 to 3800 rpm with the max rpm adjustment on the throttle arm against the stop. And from there the real adjustments can begin. Get someone to hold the lever against the stop while you check the tach? Forget the peddle for now.
Try taking the seats out remove the tray and access the front of the engine from the service door under the tray
Maybe use gorrila tape and tape the tach in position and read it with a mirror or something while you adjust the gov.
18 mph running. Top speedok it’s just me and what ever I can get to get the throttle up and take a reading. No fixed tech yet. I got 1440 low idle and 3540 pedal pegged. Call it 3600 cause I had a little bit more 1/2” to go ( stick to short
tomorrow. I’ll figure it out. Thank you
This only works if you follow the steps in exact order. When done you will have eliminated the common misadjusted control functions and then you can move from there with confidence.
Ok. Thanks for your patients. I’m sitting at 3750 rpm at high stop. 1/8” of stop using pedal. 1450 at low idle stop.
Ok great. Now we move on to the good stuff.
1. Disconnect the throttle cable from the governor control lever..disconnect the control linkage from the hst speed control lever on the rear of the transmission.
2. Confirm that the bellcrank is centered in its detent.
3. Loosen and adjust the pedal stop under the go peddle all the way down.
4. Gently push the go peddle down until all of the travel in the peddle is taken up without distortion of the peddle.
5. With the peddle pushed down without distortion readjust the peddle stop up until it touches the peddle and tighten the jamb nut.
6. Hold the peddle down against the now properly adjusted peddle stop and readjust the hst control rod so that the hst speed lever is at max travel less just a hair as to not be at hard stop.
7. With the peddle still against the stop reconnect and adjust the cable to the governor control lever so that the governor control is just touching the high idle stop without making the cable to tight.
8. Now release the peddle and cycle it a few times then put it against the stop again and hold it there while you check that these all happen at exactly the same time. Peddle against stop...governor against high idle stop without stressing the cable and the hst speed lever at max travel.
1. Disconnect the throttle cable from the governor control lever..disconnect the control linkage from the hst speed control lever on the rear of the transmission.
2. Confirm that the bellcrank is centered in its detent.
3. Loosen and adjust the pedal stop under the go peddle all the way down.
4. Gently push the go peddle down until all of the travel in the peddle is taken up without distortion of the peddle.
5. With the peddle pushed down without distortion readjust the peddle stop up until it touches the peddle and tighten the jamb nut.
6. Hold the peddle down against the now properly adjusted peddle stop and readjust the hst control rod so that the hst speed lever is at max travel less just a hair as to not be at hard stop.
7. With the peddle still against the stop reconnect and adjust the cable to the governor control lever so that the governor control is just touching the high idle stop without making the cable to tight.
8. Now release the peddle and cycle it a few times then put it against the stop again and hold it there while you check that these all happen at exactly the same time. Peddle against stop...governor against high idle stop without stressing the cable and the hst speed lever at max travel.
Whew. I’m gonna have to stare at it for a while to get it to make sense but hey I made it this far. Press on!!!! Thank you. Lots of linkages. I’m pretty sure I get. Diving in tomorrow
Be careful to follow the order exactly. It takes to much to explain
Ok. Had to stop for the evening. Quite a dance with linkages. I get full throttle now but now the idle is high. The only way to achieve the high stop ( because the throttle has only so much travel was to shorten the cable just a bit. I could not get peddle down and then idle down. I think I get the idea. Disconnect cable and hvt link Set floor stop, pin it down, set cam pivot at high point. I’m using my words vs detect. Adjust hvt rod to max forward minus a hare. Reconnect check throttle is at upper stop at full peddle. but there is only so much pivot on the throttle it won’t return to idle. I traded Max rpm for low rpm going up. What am I missing
In order to get an idea i need to ask a few questions. Has the push pull cable between the peddle and the bell crank been ajdusted? With the peddle at the top of its travel and the bell crank in detent is there adjustment possible on the push pull cable to raise the peddle?