RTV Maintenance Schedule Chart

[Doc]

For easy reference ...

GENERAL CHECK POINTS MAINTENANCE TABLE:​

Please note: this table is generic for all Kubota products. We recommend that you consult the Operator's Manual for information on your specific model.

Check Points	Hour Meter Reading: Check or Change Every Interval Shown Below	After Purchase
	50	100	150	200	250	300	350	400	450	500	550	600	650	700	750	800	850	900	1000	1st Yr	2nd Yr
Engine oil & filter change	x			x				x				x				x			x
Transmission fluid change	x					x						x						x
Hyd. Oil filter cleaning	x					x						x						x
Front diff./wheel case oil change						x						x						x
Steering gear case oil						x						x		x		x		x
Battery electrolyte level		x		x		x		x		x		x		x		x		x
Greasing ALL zerks		x		x		x		x		x		x		x		x		x
Clutch pedal play		x		x		x		x		x		x		x		x		x
Brake pedal play		x		x		x		x		x		x		x		x		x
Toe-in check		x		x		x		x		x		x		x		x		x
Front axle front-back play				x				x				x				x
Clean air cleaner element		x		x		x		x		x		x		x		x		x
Clean radiator screen and check coolant level	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x
Fan belt tension			x			x			x			x			x			x
Fuel filter element						x						x					x
Valve clearance check																x
Check tire pressure	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x
Check tire wear	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x
Check all safety switches for correct operation	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x
Replace cooling system Anti-freeze																				x	x
Replace air cleaner																	x			x	x
Check power steering hoses																				x	x
Check fuel lines																				x	x
Check radiator hoses																				x	x

 

[Doc]

I am looking for an image showing where are the zerk fittings are. Will post once I find it.

 

[bczoom]

I am looking for an image showing where are the zerk fittings are. Will post once I find it.

Thanks. I put the grease gun on the RTV the other day but do need all the locations. My manual is buried.

 

[Doc]

Didn't find anything on the internet but I had a downloaded free manual for the x1100c. Hope it helps.

 

[ETF]

I'd be interested in that too.

I'm a great believer in grease. My father taught me. One of his sayings was, "Never spare the grease son. It's a lot cheaper than replacement parts".

 

[10-e-c-dirt]

I'm a little Confused.
The manual that came with my 2022 X900 says change the hydraulic tank oil at 200 hrs and then at 400 hrs and 600 hrs, every 200 hrs.
And both hydraulic filters (yellow & black) my manual calls them transmission filters at 50 hrs, 200 hrs, 400 hrs, 600 hrs, every 200 hrs.
And the transmission fluid at 400 hrs, 800 hrs every 400 hrs. the chart above says every 300 hrs.
This is on pages 52 & 53.
The manual is dated 2019, code # K7591-7121-6, the C of O says 2022,

Does the above chart need updating ??

 

[Smilingreen]

This is the screen captures from the 2021 Kubota WSM for the RTX X1100C. I know the owners manual and the WSM differ a bit on schedule and interpretation of them.

 

[Smilingreen]

Another thing to check for, and I only realized this a couple of months ago. Check with your diesel fuel source and make sure they didn't switch to B20. My local station did and I didn't notice it until a couple of months ago. The X1100c still starts and runs ok, but now, I am going to be adding a splash of Power Service in every fuel up.