Search results

Follow up! I received a RMA from ASA Electronics (Jensen) and wrote a full description about the stations losing pre-set values randomly. The radio was returned promptly with a note saying that after 4 hours of continuous use it operated flawlessly! They did not turn the switched wire source...

Thanks for the idea! I too had thought of putting some type of coating on it, but couldn't be sure it would last. I see this working OK on a metal dip stick, but does it work on the two plastic dip sticks (transmission and hydraulic)? These our the most difficult to read.

I always have had a tough time reading hydraulic oil levels in both the hydraulic reservoir and the transmission - really tough to read. I have often overfilled both then have to remove some! After every change it is probably important to start the engine, turn the steering wheel a few times...

I added LED front plow lights - using the wiring harness in the roof. Using the same factory wiring I added a rear work light and using the backup buzzer wiring I installed a backup lamp that works really well. This is especially helpful when plowing at night. I love the side view mirrors and...

The digital pdf version I mentioned above is convenient and inexpensive, as well as a legal version.

On my X900 I had to replace the short return tube to the hydraulic reservoir. It is preformed and cracked. It may be leaking there.

I ordered my x1110c in January of 2021 and was #23 on the list at our local dealer. I took delivery in December with a Boss V-Plow. When I picked it up the list was up to 78! It is worth the wait. I’ve been plowing more than a mile of hilly dirt roads with RTV’s since 2014. They are...

I found the complete - easy to read - service manual at eRepairInfo.com for $29.00. It is a digital download in PDF. It is 465 pages for the 2022 X1100C. You can print the pages you need as you need them. It is a one-time charge. Easy and convenient. I highly recommend this.

I have communicated with the Jensen folks and I am to send it back. They gave me a RMA. We will see!

Actually it was a puff of Kubota Orange smoke!

I just took delivery of the new machine in December and have not had the radio out. I have not disconnected the power. I'll pull the 5 amp fuse. That is a good idea. The interesting thing is it is somewhat sporadic - and never happens when the radio is off when I start the machine up - only...

The lighted dial never fades and the clock has never had to be reset. The lighted dial shows no dimming when the starter is engaged. In fact this has only happened when the engine is warm and previously run. Never when starting in cold and when the glow plug has needed to be used and the...

Mine has not randomly started on it own, but the presets are lost. Interesting!!

I have the factory Jensen HD radio and the problem I have is that it quite frequently clears all the stations I have programmed in. It does not lose the time, nor is there a problem with loose connections. It happens after about 7 starts when the radio is left on. There is no interruption in...

It took some argument on my part, but Kubota did repair my broken bracket and they did weld the exhaust pipe to the manifold. I was without my machine for the better part of two weeks. I think it happened at about 600 hours as well. It was still fine when I sold it 7 years later with 11,000...

I had the same problem with my 2014 X900. Turned out to be a separation at the exhaust manifold. The muffler was press fit into the exhaust manifold with no reinforcement of a weld. The joint separated enough such that the entire muffler would vibrate enough so that the rear bracket would...

My cab is so tight I have to slam the door! The only dust that comes in when I stop and open the door and the dust I just kicked up follows in. I just use compressed air to blow it out. Before leaf-out my roads dry out really fast and now that leaves are coming out the dust will diminish.

I started a thread on this subject a few months ago. I use some heat shrink tubing and it has worked really well.

Thanks to you for providing the great information I ordered the materials and have installed a backup lamp and it is wonderful! Installation was fairly easy - kind of tight on the hands, but it worked out well. The second picture is with all the lights out in my shop so the light is certainly...

The screen looked fine but when we put diesel fuel in it nothing passed through. Not a drop!